The Oster line of pipe & bolt threading machines has served the industrial world for over 125 years. Our rugged, heavy-duty equipment is built to last decades in factory production environments. With unmatched production and power capabilities, Oster threading machines are the highest quality and longest-lasting industrial pipe and bolt threaders produced today. Oster pipe and bolt threading equipment is reliable, accurate, and available in multiple models with various configurations.
Click here to get more.
Not sure which bolt and pipe threader is best for your needs? Contact us or request a quote, and our team will gladly assist you in finding the best threader for your application. Purchasing a threading machine that meets your exact needs is crucial. Depending on your application, you’ll need to consider the requirements for your pipe and bolt threader, including:
The 792ALX Threading Machine is our flagship pipe and bolt threader. The 792ALX features high production rates at a low entry cost. The rotating X1 Diehead allows for increased production over a standard bolt and pipe threading machine and also creates a safer work environment because the concern over long pieces of rotating material is eliminated. The 792ALX can produce up to 200 threaded ends per hour and cut right and left-hand threads in a single pass.
General Specification Pipe Threading Capacity: 1/8" to 2" Bolt Threading Capacity: 1/4" to 2" Standard Die-Head: Oster Rotating Die-Head Die Symbol/Style Used: X1The 792 / 794 LX Threading Machine is oriented for heavy-duty production, with a 2” bolt and pipe threading capacity. This machine can change spindle speeds at the flick of a wrist with the infinitely variable frequency speed drive. The 792 / 794 LX can be equipped with Swing-Over style tooling for convenient pipe threading or Slide-In style tooling for left-hand and right-hand bolt threading.
General Specifications Pipe Threading Capacity: 1/8" to 2" Bolt Threading Capacity: 1/4" to 2" Standard Die-Head: Quad Slide-In, Universal Slide-In Die Symbol/Style Used: Quad and 300The 784 Threading Machine is the world’s most rugged and versatile quality-built 4” Bolt and Pipe Threading machine. Capable of cutting both right-hand and left-hand threads, Victaulic grooving, cut-off, beveling, weld prep, and more. This machine will do almost anything you can think of in the pipe threading and preparation realm and will continue doing the job for decades.
The 716 Threading Machine is a versatile pipe & bolt threading machine with a single diehead covering a 1” to 6” pipe range.
General Specifications Pipe Threading Capacity: 1" to 6" Bolt Threading Capacity: 1" to 4" Standard Die-Head: One, adjustable to handle all sizes in the stadard range Die Symbol/Style Used: 704 - 6The 8R Threading Machine provides the finest quality, design, and performance in the category of large-capacity pipe threading machines. The 8R Threading Machine can thread up to 8” NPT Pipe in a single pass.
General Specifications Pipe Threading Capacity: 2 1/2" to 8" Bolt Threading Capacity: 2" to 6" Standard Die-Head: One, adjustable to handle all sizes in the stadard range Die Symbol/Style Used: 8RThe 12R Threading Machine is one of the largest pipe threading machines currently available, capable of threading up to 12” NPT Pipe in a single pass. These machines are exceptionally durable and last for generations.
General Specifications Pipe Threading Capacity: 3 1/2" to 12" Bolt Threading Capacity: N/A Standard Die-Head: One, adjustable to handle all sizes in the satandard range Die Symbol/Style Used: 12RThe 582A Threading Machine is a high-production portable bolt and pipe threading machine with the X1 Rotating Die head. With a rotating diehead the workpiece remains stationary, improving production rates and providing a safer work environment. Capable of threading pipe or bolt, right-hand or left-hand threads available.
General Specifications Pipe Threading Capacity: 1/8" to 2" Bolt Threading Capacity: 1/4" to 2" Standard Die-Head: Oster Rotating Die Head Die Symbol/Style Used: X1The 582A Threading Machine is a high-production portable bolt and pipe threading machine with the X1 Rotating Die head. With a rotating diehead the workpiece stays stationary, improving production rates and providing a safer work environment. Capable of threading pipe or bolt, right-hand or left-hand threads available.
General Specifications Pipe Threading Capacity: 1/8" to 2" Bolt Threading Capacity: 1/4" to 2" Standard Die-Head: Quad Slide-In (582), Universal Slide-In (582), Quad Swing-Over (584) Die Symbol/Style Used: Quad and 300The 654 / 655 Threading Machine provides a versatile, heavy-duty, portable pipe, conduit, and bolt threading machine. The 654 / 655 Threading Machine can be equipped with either Swing-Over style tooling for easy pipe threading or with Slide-In Style tooling capable of cutting left-handed and right-handed bolt threads.
The Handy-Thread machine is ruggedly constructed, and fully adjustable in every way. The standard machine will cut or roll threads from 1/8" through 5/8" N.C., N.F., or 16mm with the proper heads.
The standard non-reversing machine uses a 1-1/2 HP, RPM, 115 volt, 60 Hz, single-phase electric motor with 3-prong grounded plug. It should be plugged into a 3 prong grounded receptacle with 20-ampere capacity on 115 volts.
The standard machine requires a compressed air supply of 85 PSI minimum gauge pressure, with a flow capacity of about 1/2 SCFM (standard cubic feet per minute). If no compressed air is available in the plant, or a stand alone unit is desired, a small air compressor of 1/2 HP which will deliver at least 85 PSI should be adequate for most jobs. The compressor should be used with a receiver (storage tank) of 10 to 30 gallons capacity.
Modern chemistry is developing many new and improved cutting fluids. Contact your local supplier of cutting tools if you have no special source for purchasing cutting fluid. The fluid should have a viscosity of no higher than 200 SSU (rated at 100°F). A minimum of 5 quarts and a maximum of 8 quarts is required in the Handy-Thread reservoir. When filling the reservoir, pour the fluid into the chip pan. It will drain through the chip screen into the reservoir.
Caution! Do not mix cutting fluids of different kinds because of the possibility of forming gums which will clog the pump, the coolant tube, or die head.
If the fluid discharge tube should become clogged it can usually be cleared with a blow gun without removing it from the machine. Blow backward through the tube. If necessary to remove it for cleaning, unscrew the pipe where it comes out of the machine base plate and pull the tube out.
Caution! Running the pump without cutting fluid may damage it. If fluid is not desired for threading certain materials, turn the pump off with the selector switch on the electric control box.
If the cutting fluid is too thick (viscosity too high), the pump may have difficulty in picking it up when the machine is first started and the fluid is cold. This may happen even with thinner fluids in cold weather.
Caution! Do not use flammable or aromatic solvents to thin the cutting fluid because of the danger of fire.
To install or remove a complete die head, remove cutting fluid guard and loosen (about 2 turns) the socket set screw(s) in the spindle behind the die head. Move the die yoke latch bar to the right and lift the bronze die yoke out of its groove in the die head. The die head is now ready to be removed by pulling it toward the operator. Do not hammer on the die head if it is tight; drive a thin wedge or screwdriver between the die head and the spindle.
Some die heads have die blocks which can easily be removed while the die head remains in the machine. This allows a quick change of thread size or thread lead. Consult the instruction manual for your particular brand of die head and proceed accordingly.
To re-install the die head, slip the shank into the spindle hole. Be sure the flat on the die head shank is exactly in the center under the spindle set screw(s). Tap the die head lightly with a soft hammer until its base seats against the end of the spindle, then tighten the remaining set screw(s) in the spindle, drop the die yoke into its slot, pull the yoke latch bar to the left, and re-mount the cutting fluid guard. Next, select the proper size rod guide bushing which mounts on the carriage plate and twist 1/8th turn clockwise. The rod guide bushings are about 1/32" larger than the diameter of the rod to be threaded.
Next, unscrew the collet retaining nut on the air chuck and remove the collet. Install a collet for the size rod to be threaded, re-assemble the collet retaining nut, and tighten.
For threading only one end of a rod, or for threading the same length on opposite ends of the same rod, first make sure there is at least 85 PSI air pressure showing on the gauge. If pressure is low, raise it with the pressure regulator located beneath the electrical control box. Turn the "Alt-Cont-#1" selector switch to its No. 1 (right) position. The indicator light located inside the selector switch should light. Set the right switch cam (the one on the longer switch bar) to the desired thread length by reading the scale at the front (operator) end of the switch bar. Tighten the knurled cam knob finger tight. If threading a material which requires cutting fluid or coolant, turn on the pump selector switch and wait until fluid begins to flow. Adjust the position of the fluid tube to direct the full stream of fluid onto the rod just before it enters the die.
Insert the rod to be threaded through the rod guide bushing and collet, stopping it against the swing stop arm. Gently push the carriage toward the die head. Do not bump the rod into the die head because it may chip the chasers.
If you are looking for more details, kindly visit Yushi.
After engaging the rod into the die head about 1/8", the rod will be pulled along by the die until the switch cam is contacted, at which time the die head will be automatically opened by the die head air cylinder.
Caution! Do not start to thread unless there is at least 85 PSI air pressure. The gauge is mounted on the collet air valve. Without sufficient air pressure the collet will not clamp the rod securely, and the die head will not open when the switch cam is actuated. If, after starting to thread, you discover the air pressure to be less than 85 PSI, turn off the electric motor as quickly as possible to prevent the collet from jamming into the die head. Use the "Stop" push button on the control box.
Note: For threading rods which are shorter than about 7" long, the rods must be inserted into the collet from the opposite side. In this case the rod guide bushings and the swing stop assembly are not used. The accessory twist-on stop rod assembly (furnished with each Handy-Thread machine) is inserted in place of the rod guide bushing, and adjusted to provide a stop of the proper depth as the rod is inserted into the collet. Rods as short as 1" long can be threaded in this way. The swing stop assembly may be left in place while threading short rods, or if a large number of short rods are to be threaded, the complete swing stop assembly can be taken off by loosening the two socket head screws on the top of the stop rod bracket.
In using the accessory twist-on rod stop assembly, the measuring rules on the switch bar will not be usable. A trial cut will have to be made, and if the thread length is too short, the switch cam will have to be re-set for a slightly longer thread. After a little experience the correct length will be produced on the first or second trial.
Alternate threading is the cutting of threads on opposite ends of the same rod to different lengths. The machine can be set to alternately produce a shorter, then a longer thread. The operator can thread a rod on one end then withdraw it and re-insert the opposite end for a different length thread. To set the Handy-Thread machine for alternate threading, first turn the "Alt-Cont-#1" selector switch to its "Alt" (left) position. The indicator light will light only on every other carriage stroke. When it lights, the next thread length will be that set on the right switch bar cam, usually the longer thread length. Next, set the left switch bar cam for the shorter and the right switch bar cam for the longer thread length. As the machine comes from the factory, the shorter switch bar cam can be set for up to 3-1/2" and the right switch bar cam for up to 6" thread length.
Continuous threading is the cutting of threads longer than 6". To set the Handy-Thread machine for continuous threading, first turn the "Alt-Cont-#1" selector switch to its "Cont." (middle) position. During this mode only the right switch bar cam is active. When the length set on the right switch bar is reached the chuck is opened and the head remains closed. Caution: at this time the rod will spin, so provisions must be made to insure operator safety. When the carriage is returned to the neutral (back) position, the chuck will close on the part and allow an additional length of rod to be threaded. Continue to cycle the length of the rod you wish threaded. Just prior the last cycle of the desired threaded length, switch the "Alt-Cont-#1" switch to "#1" (left) position. When the right switch bar is reached this time, the head will open. Turn off the machine to stop the rotation of the head and to release the rod from the chuck. It is important to turn off the machine prior returning the carriage the neutral position to prevent damage to the threads. To determine the setting for the right switch bar, divide the length of the desired thread in to even cycles less than 6" (ie. to cut a 15.75" thread, set the switch bar to 5.25" and run for 3 cycles).
Standard accessories furnished with the Handy-Thread machine include five sizes of quick-change rod guide bushings, each with a hole slightly larger than the rod to be threaded. These bushings are for supporting the rod and guiding it into the collet. Also included is the accessory rod stop for use in threading very short rods. This stop is used in place of the swing stop for short rods, and twists on to the carriage plate.
The standard machine uses standard No. 11 collets. These are not furnished unless specified on your order. Round collets in increments of 1/64" in diameter from 1/8" through 13/16" are available from AAA Products. Larger rods, up to 1" in diameter, can be held by using an optional special collet sleeve, collet retaining nut, and using a standard No. 21 collet. For information contact the Jiffy Products Division of AAA Products International. Special collets to hold hex and square rods are also available from the factory.
The kind of material, its hardness, and its diameter will determine the maximum spindle RPM which can be used. The standard machine is assembled with motor and spindle pulleys to have a speed of 400 RPM on the spindle. This is a good speed for a wide range of threading jobs, for cold rolled (low carbon) steel up to 1/2" in diameter with the right cutting fluid. Larger rods of this material can usually be threaded at this speed although die chaser life may be reduced. However, on long production runs, spindle speed should be reduced on rods larger than 1/2" in diameter. It is quite important that the proper amount of the right cutting fluid be used and that it be directed on the rod as close as possible to the place where the material enters the die.
If rods of less than 3/8" diameter are to be threaded in quantity, the spindle speed can be increased by replacing the motor pulley with one of larger diameter. We recommend your die manufacturer be consulted for best surface speed of a particular material along with recommendations on lubricant or coolant.
For threading harder materials such as stainless steel or higher carbon steel, the spindle should be run at a slower speed. The standard pulley supplied on standard units may be replaced with an optional pulley. These are standard timing belt pulleys for a 1" wide belt, and can be purchased either from the factory or from a local power transmission dealer. It is unimportant to change the pulleys for a short run of small rods.
For best production rate the machine should be run, if possible, at the highest RPM or surface speed (SFM) recommended by the head manufacturer. When running at higher speeds, particularly on large diameter rods, or when threading harder materials, it is especially important to use the right amount of the right cutting fluid and to see that it is directed properly.
Remove the drive belt guard and loosen the belt tension adjusting knobs. Remove the belt and the motor pulley. Install the replacement pulley. Align the motor and spindle pulleys, then tighten the pulley screws. Install the belt, then adjust the belt tension knobs to produce a light tension on the belt. Install the belt guard. Caution! Do not operate the machine without the belt guard in place.
The Handy-Thread machine is built for long life and rugged daily use; the die head chasers are the only parts which may have to be replaced on a regular basis. The following simple adjustments may be required occasionally:
Air Pressure
The air line pressure should be adjusted until the air pressure gauge on top of the air
clamp valve reads at least 85 PSI. This adjustment is made on the pressure regulator which
is located under the electric control box. After setting the pressure, cycle the machine
once without cutting threads, to be sure the pressure has stabilized.
Drop Stop
This is set at the factory 6-1/8" from the stop rod mounting bracket. The length of thread
cut when the switch cams are set, can be varied about 1/8" plus or minus by loosening the
two socket head cap head cap screws in the left side of the stop rod mounting bracket, then
sliding the stop rod in or out until thread lengths cut on a test rod correspond to the
length to which the switch cams are set on the switch bar rules.
Switch Bars
Each of the two switch bars can be adjusted to make the thread length longer or shorter by
1/16" each way. This is done by loosening the lock nuts on each end of the switch bars, then
loosening one socket set screw and tightening the other. These 60° socket set screws
should
be set so there is no side movement or end play, but so the switch bar will rock freely;
then tighten the lock nuts and check the movement again.
Die Head Adjustments
Refer to the die head instruction manual for the brand and model of the die head being used.
Note: When using water soluble cutting fluids, all die head models will require periodic disassembly, cleaning, and oiling to remove gum and rust. The need for cleaning will be obvious from the sluggish opening and closing of the die head.
Centering Die Head Horizontally on the Collet
If it should become necessary to re-center the die head on the collet in a horizontal
direction, slightly loosen the four 1/2" hex head bolts which hold the main spindle bearing
blocks to the machine base plate. Tap both bearings to the left or right as required.
The main spindle should measure parallel to the ball bushing rod so that when a straight rod is chucked in the collet it will hit the center of the die head when the carriage is pushed toward the die head. After making this adjustment, firmly tighten the four hex head bolts.
Centering Collet Vertically on the Die Head
Raising or lowering the collet so it will be in alignment with the die head is done with the
two cams (upper and lower) which support the carriage plate. These are located near the
operator, on the left side of the machine.
Recommended adjusting procedure is to take a headless bolt and screw it into the closed die until about 1" of its unthreaded end is protruding out of the die. Disconnect air pressure or unplug the electrical power so the collet will not close. Push the carriage forward and adjust the carriage support cams so the collet will slide freely over the headless bolt. Each cam is adjusted by slightly loosening the socket head cap screw going through its center, then rotating the 5/8" hex cam to the desired position. Tighten the screw while holding the cam to keep it from rotating. When properly adjusted, there should be no up and down play in the carriage.
Replacing an Electrical Limit Switch
There are three limit switches, and any one of them can be replaced by removing the four
1/4" socket head cap screws holding the switch assembly. The switching assembly can then be
moved back and out from under the switch cam collar. Turn the switch assembly on its side to
remove a switch. All switches are Omron switch No. Z-15GD55-B7-K.
When replacing a faulty limit switch, remove only one wire at a time. Connect this wire to the same terminal on the new switch before removing another wire.
The three limit switches can be identified as follows: the one mounted crosswise to the others operates the collet solenoid air valve (the one with a gauge mounted on it) and also re-cocks the die head through the double solenoid air valve. The switch next to it (in the middle) is actuated by the left switch cam bar. When actuated, it opens the die when thread length is reached, but is operative only when the "Alt-Cont-#1" selector switch on the control box is in its "Alt" (left) position for alternately threading to different lengths on opposite ends of the same rod. The third switch also opens the die when actuated. It opens the die on every threading operation when the "Alt-Cont-#1" switch is set in its No. 1 (right) position and on every other threading operation when the "Alt-Cont-#1" switch is set in its "Alt" (left) position.
Want more information on Heavy duty model rod threading machine? Feel free to contact us.