There is an increase in construction projects, which is why buying new construction equipment is essential. Buying an old machine is okay until it starts giving you troubles by requiring constant maintenance and part replacement.
SINOCOREDRILL are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.
If you have a long term project, it’s better to buy a new machine than an old machine. The first thing to remember is to order your equipment from a reliable source. One of the construction equipment is ZLCONN HDD machine which is manufactured and assembled by its ZL Conn Company.
Here are key points to mull over before buying a horizontal directional drilling machine.
There is a common phrase; quality is key. It’s better to spend extra money on an HDD machine that is of quality than spend less on a bad quality machine. The quality of a machine determines the safety of your employees and work quality.
If the machine fails to reach the optimal threshold, it will degenerate quickly under harsh conditions, which will then lead to your employee working with compromised equipment. It is therefore essential for horizontal directional drilling companies to take into account the quality of the HDD machine before purchasing.
Construction equipment is generally expensive. But, it’s better to buy the equipment at a costly price, but they will last through your infrastructure project. However, check on the horizontal directional drilling price list and acquire relevant information on the prices of the HDD before purchasing the equipment.
Technology is a friend of a business person. It has enhanced the efficiency of work. Choose a horizontal directional drilling machine that is built with the latest technology because it will require less manpower, and your company will spend less time completing construction projects.
Secondly, as it was mention earlier, construction equipment is costly. So, some companies can’t afford it, especially if the company is starting up. But, such construction companies will hire your machine because they know it’s built with the latest technology.
HDD consumes fuel as it operates. So, when choosing an HDD, consider the fuel consumption rate because fuel consumption can increase operation price in the long run.
Working in a construction site is hazardous if the person handling machinery lacks expertise and experience. So, before purchasing a horizontal directional drilling machine, invest in training persons that will be operating the machine. Besides, who will aid you in deciding on HDD machine specifications?
Is the supplier the same as the original HDD drilling machine manufacturer, or is he a middleman? Whichever answer it is, the supplier should answer your questions correctly. The answer should determine whether the supplier is reputable and reliable or if he is just in the market to make money. If he is running his business to make money, it means, when you encounter machinery problems, he won’t be of much help.
Conclusion
Buying a new HDD machine is advantageous in the long run because it will operate for a long time before you need to service it. But consider all the necessary tips and don’t compromise. They will determine whether you’re going to acquire a machine that will give value to the amount you’re spent buying it.
By Joel D. Moore, PE
If you want to learn more, please visit our website Directional Hdd Machines for sale.
Over the past 25 years I have been involved with designing and inspecting Horizontal Directional Drills (HDD) for pipeline construction. I have attended numerous seminars, purchased many texts, and read countless white papers related to the subject. Of much more educational value (and fun) is the many hours I have spent on drilling sites asking questions and listening intently to the folks running the drill. Listening to all of the “hands” on the site that know a lot more than “those engineers” has taught me several Rules of Thumb for HDD design. So now that I am starting to turn a bit gray, I think it’s time to share my Rules of Thumb. If you are looking for a technical dissertation, there are plenty of papers and books on the subject with much more engineering and experience behind them than what you will find here, and while I am interested in the subject, this is just my “Totally Biased Opinion”.
You paid a lot to have your Geotech crews mobilized. Make it worth your while by drilling multiple holes on each side of the feature you are looking to cross. Two as close to the feature you are crossing, and 20’ to 25’ to the right and left of your designed bore path (that’s four holes right next to the stream or road or other feature). Be smart and have the holes grouted in when they are done. Drill deeper than you think that bore path will be. Drill another set of core drills near the entry and exit points. Again, drill to each side and offset from your designed path. For a long drill, and in areas where the near surface geology changes a lot, drill even more sets. If you have good reason to believe that the subsurface is consistent then you can back off the number or core drills. If it isn’t, then the money spent on Geotech information will save many times that amount in the HDD driller’s bid price and if they know where the cobbles and solid rock is (for instance) you will save even more and have a better chance at success. Don’t forget to share the information with the bidders.
The conventional wisdom is (or was) 100 ft radius per 1-inch of pipe diameter. However, what really happens is that the pilot drill hole drill path is rarely an actual nice smooth radius. It’s usually more of a series of short straight drills, curves of various radius, and lots of “corrections”. The Driller will set the “Bent Sub” to a specific angle and can rock the drill string back and forth to create a desired radius, but my experience is it may or may not be a very smooth curve. Lots of Drillers today will prefer a design with a 120 ft/1 in pipe diameter, and I believe that this is a minimum. As we use higher and higher yield strength and heavier wall pipe, the drill string becomes pretty stiff on pull back, and without a smooth hole it takes a lot of force to pull it into the hole. Yes, the driller can ream out the high spots and/or ream a size larger than what would have otherwise been necessary, but a larger radius by design and a Driller with some patience during the pilot drill will pay off. If you find that the pullback force is really high even though you are in nice rock, then you might be damaging the pipe coating on the spots that are causing interference. You won’t necessarily see that on the first half of joint of pipe either.
The diameter-to-wall thickness ratio (D/T) needs to be less than 50. First, it will give you a better chance of not having the pipe collapse during pullback, and second, it will give you more wall thickness to compensate for gouges. I’ve witnessed a collapse first-hand with a now abandoned 10” pipe under the Allegany River near Olean, New York, “installed” in the late ’s that was too thin given the diameter.
Specify PowerCrete rather than Abrasion Resistant Overlay (ARO) for your pipe coating. If you really care about protecting the Fusion Bonded Epoxy (FBE) coating and your steel from corrosion, then specify PowerCrete. A good spec is 40 mils PowerCrete R-95 over 14-16 mils FBE. ARO is good for installing pipe in road/stream crossings or somewhere that it is difficult to pad the pipe or install rock shield. The PowerCrete product will have greater abrasion resistance, a lower coefficient of friction, and looks nicer. Use the right PowerCrete product to coat your welds and make sure that they are prepared properly. Don’t forget to hire a NACE inspector to inspect the coating on the welds (*this is not a paid advertisement, I promise).
Drilling around a corner is fine for plastic pipe and maybe small diameter steel, but it is torture on the drill pipe and difficult to get a nice smooth hole. There is a way to design it so that the pipe passes through just one plane, but it takes a lot of geometry (3D CADD works well to design those drills). Extra bends/curves add to the possibility of increased downhole mud pressures and the potential for an inadvertent return. It is best to figure out another way to get from Point A to Point B if possible.
The DC tracking system used for many years to steer the pilot bore is a must for any serious HDD crossing. Be smart, and don’t let the contractor shoot in the dark. If he is willing to do that, find another driller.
Be very careful here and do your research for proper contract language. At one extreme, you will pay too much, and at the other extreme, you will inadvertently encourage the contractor to cut corners to keep from losing their business. You don’t want the Driller to “just pull the pipe in”.
Be ready for inadvertent returns (IR). Directional Drills have the potential to release drilling fluids (primarily a Bentonite clay-water mixture) to the surface through Inadvertent Returns (commonly referred to as “frac-outs”). Prepare a contingency plan in advance that addresses personnel responsibilities, response procedures, containment materials, appropriate cleanup procedures, and proper documentation. The purpose of the contingency plan is to minimize the potential for an IR, provide for timely detection, ensure proper notifications are made, protect areas that could be considered environmentally sensitive, and ensure an organized and timely response in the event of a frac-out. Lastly, tell the permitting agency that you are doing everything possible to prevent an IR, but just in case present the contingency plan.
While this has nothing to do with the design phase of an HDD project other than perhaps giving yourself additional space on the exit side to put the drill rig, it seems that every time I have witnessed a broken drill string, it broke while a reamer was being pushed. Just imagine a 6” steel rod extended ’ into a 30” hole, and pushed hard enough, it will begin to snake back and forth. Euler figured out a long time ago that you shouldn’t push a long slender rod too hard or would buckle. Now imagine rotating the whole thing fast when the reamer is likely taking a lot of torque to turn it, or the drill rod is making 3 or 4 revolutions at the HDD rig, and the rod is getting all wound up before the reamer breaks loose. Imagine the fatigue the drill rod has experienced. Do it for a little while with old drill pipe, or a long while with new drill pipe, and you will find out. Then what do you do when the driller says, “we have to do it that way”? If you are feeling generous or really need to get it done, see if there isn’t an opportunity to get another rig in there on the exit side and maybe salvage what you have before you twist off.
This is the final and most important tip! The key word here is “competent”. If the contractor is the low bid, then you probably don’t want them. If you don’t have a history with them, then ask for the names and contact information for the last 10 drills that they did of similar size and length. Ask if they have drilled in the local area and their history in the type of soils they are going to encounter. Most importantly, ask who will be the actual “Driller” or “Drillers” controlling the drill bit, and what is/are their experience level? If they are arrogant or in a hurry, good luck. They should be confident and should be optimists, or they wouldn’t be in the business. However, if your Driller pushes hard and drills a winding pilot hole with lots of “corrections” then you are in trouble at the get-go. Slow and steady, focused, intelligent, knowledgeable, listens to others are all good traits. If the driller is proud of how many times they were successful at “fishing” a broken drill stem (that they broke while pushing the reamer), then ask them if they know any good drillers.
The bottom line is this: Anyone with rudimentary CADD skills can design an HDD. Anyone with some money can buy a used HDD rig and go into the drilling business. Anyone with some luck can drill down into the ground and come up somewhere on the other side of the road or river. But if you need to have the pipe still be round and hold pressure at the end of the day, then plan accordingly, follow the rules, and hire the best driller you can find.
Joel Moore is a licensed Professional Engineer that has worked in the transmission and distribution gas industry for over 30 years, with over 20 years of experience with HDD’s. In , Mr. Moore sold his company, Integrity Engineering PLLC to Montrose, PA based JHA Companies, where he continues to perform HDD design and consult on troubled bores.
Want more information on Water Well Rigs? Feel free to contact us.